Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Conroe Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning and service in Conroe, and what sets our Gelco work apart is that we treat the cap as a system component, not an accessory. That means we measure the flue tile, check the screen and fasteners, and match replacement hardware to the flue that’s actually there instead of reaching for a universal cap. Gelco is a chimney cap brand, and caps are where a lot of Conroe chimney problems start and end. We are an independent service provider. Chimney Sweep Conroe is not affiliated with, authorized by, or endorsed by Gelco, and we never claim to be. What we are is experienced with Gelco caps and the flues they sit on: our technicians have up to 13 years of experience, and we service homes across Conroe and the surrounding Montgomery County properties. Clean flue. Sound liner. Safe fire. Call (888) 401-8620.
Why Trust Chimney Sweep Conroe for Your Gelco Chimney Cleaning?
We read Gelco’s own installation and clearance documentation and work from it. That sounds like a small thing until you’ve seen a cap seated on the wrong flue tile with hardware that was never meant for it. Every Gelco job starts with the paperwork: what cap is installed, what it’s covering, and what the manufacturer specifies for clearance and fastening. Then we match venting, hardware and termination details to what’s actually on your roof. Not a generic “universal” spec, and not whatever was left in the truck.
We don’t stock or sell genuine Gelco parts, and we’re not a Gelco dealer. We use quality parts that fit Gelco equipment, and we say plainly which is which when we quote. That matters for your warranty. Manufacturer warranties on chimney caps and related components generally hinge on proper installation and correct sizing, so we install to spec and document what we did. If a cap has failed because it was the wrong size from day one, that’s an installation problem, and we’ll tell you so.
We handle the full cycle here: cleaning, structural repair and inspection. One company discovers the problem and one company fixes it. No handoffs, no “the sweep found something, call a repair guy.” You get a photo record of what we found and a written estimate for what it takes to correct it.
Key Takeaways
- We are an independent Gelco service provider, not an authorized one.
- Gelco is a chimney cap brand; our Gelco work focuses on caps, screens, dampers and the flues beneath them.
- We work from Gelco’s installation and clearance documentation, not generic specs.
- We use quality parts that fit Gelco equipment, and we don’t claim to stock OEM components.
- Cleaning, repair and inspection come from the same company.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Conroe
Conroe’s climate is hard on caps in a specific way. Subtropical Gulf humidity sits on metal for most of the year, and dormant chimneys stay damp from spring through fall. Then the December cold fronts hit and people burn daily for weeks, loading the flue with creosote fast. Pine pollen and needles from the surrounding woods add another layer. Here’s what we actually find on Gelco caps in Conroe:
- Cap screen corrosion and insect-screen clogging. Pinholes open up in galvanized mesh over time. Once they do, sparks can escape, water and debris get in, and the flue draft suffers. A clogged or corroded screen is one of the most common things we pull off a Conroe chimney, and it’s often the reason a fireplace smokes back into the room.
- Cap legs and mounting collars rusting through at the flue crown seam. This is where the cap meets the masonry, and it’s where water gets in. As the legs rust, the cap shifts off-center and starts channeling rain down the flue instead of shedding it away. Rust streaks on the chimney exterior usually trace back to this seam.
- Cap sizing that doesn’t match the flue tile OD. A cap that’s a size off from the flue tile outside diameter rests loose. It rattles in wind, and in Gulf-storm gusts it can lift or blow off entirely. Sizing errors happen at installation, and they’re invisible until the cap starts moving.
- Fasteners and cap hardware seizing to the flue tile. Corroded fasteners are a real problem at sweep time. Pull a seized cap carelessly and you chip or crack the flue tile edges. That turns a simple sweep into a masonry repair, and we’ve seen it enough to check hardware condition before we touch a cap.
- Pine needle packing and critter intrusion. Piney Woods properties often have tall pines overhanging the cap. Screens pack with needles, and squirrels get into flues during the off-season. A Houston subdivision tech rarely sees this. Out here on acreage in Montgomery County, it’s routine.
A typical Gelco cap job starts with a homeowner noticing rust streaks down the chimney or water in the firebox after a storm. Inspection usually finds the screen mesh corroded through and the cap legs rusted at the flue seam. A qualified local pro sweeps the flue first, checks the flue tile crown for cracks, then measures the flue tile OD and sets a correctly sized stainless cap with fresh fasteners so the cap sheds water instead of channeling it into the tile. That sequence matters. Sweep first, inspect the crown, then size and set the cap.
Gelco Parts & Our Repair-vs-Replace Approach
We use Gelco-compatible stainless caps and hardware, or equal-grade components, rather than thin galvanized aftermarket caps. In Southeast Texas humidity, thin galvanized fails fast: the mesh corrodes through and the legs rust at the seam within a few seasons. Stainless costs more up front and lasts longer here. We’ll show you both options and tell you honestly which one we’d put on our own roof.
The repair-or-replace call comes down to what’s actually failed. When a cap is only rusted at the legs or the screen, replacing the cap assembly is usually more honest than patching it. Patches on a corroded cap don’t hold, and you’re back up there next year. When the flue tile itself is cracked, the cap is the smaller problem. We flag the tile before we quote a cap, because selling you a new cap over a cracked crown fixes nothing.
We don’t stock or order genuine Gelco parts. What we do is fit quality parts to your equipment, install them properly, and stand behind the work. If you’re not sure whether your cap needs replacing or just re-screening, call (888) 401-8620 and we’ll take a look.
What a Gelco Cap Service Covers
- Cap Replacement: removing a failed cap, sweeping the flue, checking the crown, and setting a correctly sized stainless cap with fresh fasteners.
- Multi-Flue Cap Service: for masonry chimneys serving more than one appliance, we check clearances between flue tiles and confirm the cap vents each flue properly.
- Annual Sweep: our standard cleaning visit, with the cap pulled, screen checked and hardware inspected while we’re up there. A cap is only as good as the flue it covers.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We inspect the cap, screen, fasteners and flue crown together. We measure the flue tile OD against the cap’s mounting collar, because a size mismatch explains a lot of rattling and water intrusion before we ever get to the flue interior. You see the photos.
- 2
Repair or install. If the cap is serviceable, we clean and re-fit it. If it’s failed, we set a correctly sized stainless cap with fresh hardware, matched to the flue you actually have and to Gelco’s installation and clearance documentation.
- 3
Test. We confirm the cap sheds water, the screen is clear of pine needles and debris, and the flue draws properly. Draft problems often trace back to a clogged cap screen, so this step catches what a sweep alone would miss.
- 4
Warranty and documentation. You get a written record of what was installed, sized how, and why. That documentation protects your manufacturer warranty and gives the next technician something to work from.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Conroe
Gelco makes chimney caps, and cap work is the core of what we do with the brand. We service and install single-flue and multi-flue caps in galvanized and stainless steel. For wood-burning fireplaces, we handle flue caps with spark screens, and for masonry chimneys serving multiple appliances, we work with multi-port caps that vent each flue correctly. We also service replacement dampers and top-mount damper hardware. Around Lake Conroe and the newer custom builds on the south side, top-mount dampers are common, and the hardware on them is worth a look during any annual sweep. We service and install these products. We don’t claim to stock them, and we’re not a Gelco dealer.
We Also Service These Brands
Gelco caps work alongside other professional-grade components, and we service those too. We work with DuraFlex liner systems for relining, and HeatShield for chimney resurfacing and liner repair work. Familiarity with Olympia Chimney, Famco and Copperfield rounds out our parts knowledge for caps, dampers and ventilation components. One company for the cleaning, the repair and the inspection.
FAQs – Gelco Chimney Cleaning Service in Conroe
No. We are an independent Gelco service provider in Conroe. Chimney Sweep Conroe is not affiliated with, authorized by, or endorsed by Gelco, and we never claim to be. We service Gelco caps and related equipment using quality parts that fit them, and we work from the manufacturer’s installation and clearance documentation. Call (888) 401-8620 with questions about your specific setup.
Yes. We use Gelco-compatible stainless caps and hardware, or equal-grade components, rather than thin galvanized aftermarket caps. We don’t stock, order or sell genuine Gelco parts. What we do is fit quality parts to your equipment, install them to the correct size and clearance, and tell you plainly which components are manufacturer parts and which aren’t. Call (888) 401-8620 for an exact quote on your cap.
Most Gelco cap work, including the sweep and inspection that goes with it, takes a couple of hours. A simple re-screen or cap re-fit is quicker. Cap replacement takes longer because we sweep the flue and check the crown before setting the new cap. Multi-flue caps take more time than single-flue caps. Call (888) 401-8620 and we’ll give you a realistic window for your job.
Gelco is a chimney cap brand, so our Gelco work covers caps and the flues they sit on. That includes single-flue and multi-flue caps in galvanized and stainless steel, flue caps with spark screens for wood-burning fireplaces, multi-port caps for masonry chimneys serving multiple appliances, and replacement dampers and top-mount damper hardware. Call (888) 401-8620 if you’re not sure what’s on your chimney.
Proper service doesn’t void a manufacturer warranty, and incorrect installation does. That’s why we work from Gelco’s installation and clearance documentation and document what we install and how it was sized. We’re not a Gelco dealer and we don’t issue Gelco warranties, so read your warranty terms. Call (888) 401-8620 and we’ll walk you through what our work covers.
A standard sweep with a cap inspection typically runs a few hundred dollars, and cap replacement with a correctly sized stainless cap usually runs more, depending on flue size and access. The written estimate sets the final price, and the estimate is free. Call (888) 401-8620 for an exact quote.
Often the cap should be replaced, not re-screened. Once the mesh is rusted through, the legs are usually corroding at the flue seam too, and re-screening a rusted frame doesn’t hold. If the frame and legs are sound, re-screening makes sense. We inspect both before recommending. Call (888) 401-8620 and we’ll give you an honest answer after we look.
You check the flue tile outside diameter against the cap’s mounting collar. A correct cap seats flush and doesn’t shift. If it rattles or sits cocked, it’s a size issue, and that’s an installation problem, not a weather problem. We measure it during any sweep. Call (888) 401-8620 to have yours checked.
Yes. A multi-flue cap comes off for sweeping, then goes back on with the clearances rechecked between flues. The seized-fastener risk we mentioned above is highest on multi-flue caps, so we check hardware condition before we pull one. Call (888) 401-8620 to book it.
Usually, yes. A cap rusted at the legs or seam shifts off-center and channels rain down the flue instead of shedding it. That shows up as water stains in the firebox and rust streaks on the chimney exterior. Fixing the cap often stops the leak. Call (888) 401-8620 and we’ll confirm it’s the cap before you spend money on masonry.
It can be. A rattling cap is usually undersized for the flue tile, and a loose cap can lift or blow off in Gulf-storm gusts. It also admits rain and debris at the gap. It’s worth a look before storm season. Call (888) 401-8620 and we’ll check the size and the fasteners.
Book Your Gelco Service in Conroe, TX
If you’ve got a Gelco cap on your chimney and you’re not sure of its condition, we’ll take a look and tell you exactly what’s there. Cleaning, repair and inspection from one company, with quality parts that fit your equipment. Call (888) 401-8620. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Written by the team at Chimney Sweep Conroe.