Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Cut and Shoot, TX
Chimney inspection in Cut and Shoot, TX is where most of our work here starts, because this is a community where the fireplace or freestanding stove isn’t decorative – it’s part of how a house stays warm when a hard freeze rolls through East Montgomery County. Homes on multi-acre wooded tracts, a mix of 1970s through 1990s site-built houses and manufactured homes, each with its own flue setup and its own history of wood burning. We inspect what’s inside, show you what we find, and quote what it takes to make it right. Our technicians have up to 13 years of experience. Call (888) 401-8620.
Why Cut and Shoot Homes Are Different
Cut and Shoot is unincorporated, and that shapes the work. There’s no city permitting desk handling chimney questions at a municipal counter, so homeowners here deal with Montgomery County processes and their own judgment instead of a layer of local code staff. Many properties sit on large wooded lots with long driveways, which means access matters: a truck has to get down the drive, and a technician has to get a ladder to a roofline hemmed in by mature pines.
The housing stock drives the rest. A 1970s site-built house may have a masonry firebox and clay tile flue that’s been through five decades of pine fires. A manufactured home from the 1980s or 1990s may have a factory-built metal chimney with a specific cap and vent arrangement that a generic sweep tool won’t fit. The climate adds its own twist: mild winters with occasional hard freezes push people into heavy burning during cold snaps, and the pine and hardwood canopy above these properties drops needles, leaves and the occasional bird nest onto caps and spark arrestors. Wind does the rest. A cap that was clear in October can be blocked by December.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Main Cut and Shoot Services
Two jobs come up again and again in Cut and Shoot: getting a dirty flue cleaned before heavy seasonal use, and fixing the structural problems a sweep turns up.
Chimney Sweep in Cut and Shoot
Sweeping a flue in Cut and Shoot usually means dealing with pine-pitch creosote, which sticks harder and glazes more readily than the fluff you get from burning seasoned hardwood alone. In the older manufactured homes out here, the flue diameter and the cap arrangement often rule out the standard brush a generalist carries, so the right tool matters more than the muscle behind it. A sweep here runs from the firebox up through the flue and the cap, with a camera look at what the brush can’t reach. If you’re ready to book, our chimney sweep page covers what the visit involves.

Chimney Repair in Cut and Shoot
Repair work in Cut and Shoot tends to fall into two buckets: the wash and crown at the top, where freeze-thaw cycles open cracks, and the liner inside, where glazed creosote and years of heat have done damage. We use HeatShield for resurfacing a liner that’s still structurally sound enough to repair, and DuraFlex stainless systems when a liner has to be replaced outright. Caps and dampers get attention too, since a blocked or missing cap is what lets the pine needles in. Our chimney repair page goes into the detail.

Chimney Inspection in Cut and Shoot
Chimney inspection in Cut and Shoot answers a question a sweep alone can’t: is this flue safe to use, or is there something inside that needs fixing before the next cold front. In a community where so many homes burn wood as primary or supplemental heat, and where 1970s through 1990s construction and manufactured housing put a wide range of flue types under the same pine canopy, an inspection is the only way to know what you’ve actually got. We treat Chimney Inspection as the front door to everything else – we inspect it and we fix it, no handoffs. Our technicians have up to 13 years of experience reading flues in rural East Montgomery County.
Chimney Flue Inspection
Signs you need it
You need a flue inspection if smoke rolls back into the room, if you smell a sharp creosote odor on warm days, or if you’ve burned a full season without anyone looking up the flue.
What it costs in Cut and Shoot
A flue inspection in Cut and Shoot typically runs $125 to $275, with camera work and a written photo report included in the estimate we give you before we start.
How we do it
We run a camera down the flue from the top and up from the firebox, check the joints, the liner surface and the cap, then walk you through the footage so you see exactly what we see.
Level 2 Chimney Inspection
Signs you need it
A Level 2 inspection is what you want after a chimney fire, after buying a home with an uninspected fireplace, or before switching to a new stove or insert.
What it costs in Cut and Shoot
A Level 2 inspection in Cut and Shoot typically costs $175 to $375, and the written estimate sets the final price once we’ve seen the flue.
How we do it
We inspect every accessible part of the system – firebox, damper, flue, cap, and the chimney exterior – with video documentation of each area, then hand you a report you can act on.
Chimney Fire
Signs you need it
Signs of a chimney fire include a loud roaring or popping sound from the flue, puffy or honeycombed creosote, warped metal on a factory-built chimney, or cracked tiles after a hot burn.
What it costs in Cut and Shoot
Assessing fire damage in Cut and Shoot typically runs $175 to $375 for the inspection, with any repair quoted separately and set by the written estimate.
How we do it
We inspect the full system for heat damage, check the liner and the surrounding framing clearances, document what we find with photos, and tell you plainly what can wait and what can’t.
What Chimney Inspection Costs in Cut and Shoot
These are typical ranges for the Cut and Shoot market. The written estimate you get before any work begins is the final word.
| Item | Typical range in Cut and Shoot |
|---|---|
| Flue inspection (camera + photo report) | $125 – $275 |
| Level 2 inspection | $175 – $375 |
| Chimney fire damage assessment | $175 – $375 |
Can you inspect a chimney on a manufactured home in Cut and Shoot?
Yes. Factory-built metal chimneys on manufactured homes are common in Cut and Shoot, and they need inspection too – the cap, vent arrangement and clearances differ from masonry, so we bring the right camera and tools for the setup.
Do I really need an inspection if I just want a sweep?
Yes, if you haven’t had one. A sweep clears the flue; an inspection tells you whether the liner, cap and joints are sound. In Cut and Shoot’s older housing, that distinction matters – call (888) 401-8620 for a free estimate.
Brands We Service in Cut and Shoot
We work with professional-grade chimney brands – Gelco and Olympia Chimney for repair supply lines, Famco and Copperfield for caps, dampers and ventilation components. We don’t claim stocked parts; we source what the job needs. Turnaround depends on the part, and we’ll tell you honestly when it’s a quick fix and when it isn’t. You can see the full roster on our brands page.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Cut and Shoot, TX
Every price below is a typical range for the Cut and Shoot market, not a quote. The written estimate sets the final price, and you get it before we start.
| Service | Typical range in Cut and Shoot |
|---|---|
| Chimney sweep | $150 – $300 |
| Flue inspection | $125 – $275 |
| Level 2 inspection | $175 – $375 |
| Chimney fire damage assessment | $175 – $375 |
| Crown repair | $250 – $600 |
| Cap replacement | $150 – $450 |
| Damper replacement | $250 – $600 |
| Liner resurfacing (HeatShield) | $1,200 – $2,800 |
| Liner replacement (DuraFlex) | $1,800 – $4,500 |
| Masonry tuckpointing | $400 – $1,500 |
What pushes price up in Cut and Shoot is access and flue condition. A long driveway, a roofline crowded by pines, or a flue that’s been glazed for years all add labor. A manufactured home with an unusual vent arrangement can mean extra setup. We quote upfront so you know before we climb.
Neighborhoods We Serve in Cut and Shoot
We work throughout this unincorporated East Montgomery County community, from the wooded tracts along FM 1484 and FM 2090 to the smaller parcels tucked off the side roads. Long driveways and pine-shaded rooflines are the norm here, so plan for a little extra time on access. Response to Cut and Shoot is steady – we schedule around the area’s rural layout so a visit isn’t rushed.
- FM 1484 corridor
- FM 2090 area
- Wooded tracts off the side roads
- Multi-acre parcels surrounding the community core
Service Area – Cities Near Cut and Shoot
Cut and Shoot sits close to several communities we also cover. If you’re just outside the community line, we can still help. We work in Conroe, TX, just to the west, and out to Willis, TX to the north. East and south of us we cover Shenandoah, TX and Cleveland, TX. Wherever you are in the area, the same inspection-first approach applies.
Serving Cut and Shoot, TX – Our Local Coverage Area
We serve Cut and Shoot and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Cut and Shoot
Yes. We cover Cut and Shoot and the surrounding East Montgomery County area, including multi-acre wooded tracts where access needs a little planning. Call (888) 401-8620 with your address and we’ll confirm coverage and book a visit.
Cut and Shoot is unincorporated, so chimney permits are handled through Montgomery County rather than a city desk. Requirements vary by scope, so ask the county before major structural work. We’ll tell you when a job is likely to need one.
Call (888) 401-8620. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, closed Saturday. We’ll book a time and give you a free estimate before any work begins.
Ready to know exactly what’s inside your chimney? Call (888) 401-8620 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Cut and Shoot Customers Say
"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."
- Rosa Torres"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Javier Vargas"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Jason Schaefer